dakota bulldozer, 2017-12-29 15:14:08. With the Closed-center Load Sensing (CLSS) hydraulic system, blade lever stroke is directly proportional with blade speed, regardless of the load and travel speed. This results in superb, fine controllability.
dakota bulldozer, 2017-12-29 15:22:43. Powerful S6D125E-2 diesel engine provides a massive output of 149 kW 200 HP. The engine power is transmitted smoothly to the final drives via a high-efficiency torque converter.
dakota bulldozer, 2017-12-29 15:22:36. An electronic monitoring system prevents minor problems from developing into major ones. All meters and gauges are controlled by a microcomputer, which provides a wide indication range for an easier, more precise reading.
mantan Drilling, 2017-12-03 02:54:35. Small mobile drilling rigs are also used to drill or bore piles. Rigs can range from 100 ton continuous flight auger (CFA) rigs to small air powered rigs used to drill holes in quarries, etc. These rigs use the same technology and equipment as the oil drilling rigs, just on a smaller scale.
mantan Drilling, 2017-12-03 02:54:35. The well had a particularly small mouth, "as small as a small bowl." Archaeological evidence of the drilling tools used in deep-well dwelling are kept and displayed in the Zigong Salt Industry Museum. According to Salt: A World History, a Qing Dynasty well, also located in Zigong, "continued down to 3,300 feet [1,000 m] making it at the time the deepest drilled well in the world." Mechanised versions of this system persisted until about 1970, using a cam to rapidly raise and drop what, by then, was a steel cable up to 3 mm.
mantan Drilling, 2017-12-03 02:54:36. RAB drilling is used most frequently in the mineral exploration industry. (This tool is also known as a Down-the-hole drill.) The drill uses a pneumatic reciprocating piston-driven "hammer" to energetically drive a heavy drill bit into the rock. The drill bit is hollow, solid steel and has ~20 mm thick tungsten rods protruding from the steel matrix as "buttons". The tungsten buttons are the cutting face of the bit.
mantan Drilling, 2017-12-03 02:54:36. Oil and natural gas drilling rigs are used not only to identify geologic reservoirs but also to create holes that allow the extraction of oil or natural gas from those reservoirs. Primarily in onshore oil and gas fields once a well has been drilled, the drilling rig will be moved off of the well and a service rig (a smaller rig) that is purpose-built for completions will be moved on to the well to get the well on line.
mantan Drilling, 2017-12-03 02:54:13. Hoists in the rig can lift hundreds of tons of pipe. Other equipment can force acid or sand into reservoirs to facilitate extraction of the oil or natural gas; and in remote locations there can be permanent living accommodation and catering for crews (which may be more than a hundred). Marine rigs may operate thousands of miles distant from the supply base with infrequent crew rotation or cycle.
mantan Drilling, 2017-12-03 02:54:36. Drilling rigs can sample sub-surface mineral deposits, test rock, soil and groundwater physical properties, and also can be used to install sub-surface fabrications, such as underground utilities, instrumentation, tunnels or wells.
mantan Drilling, 2017-12-03 02:54:36. There are many types and designs of drilling rigs, with many drilling rigs capable of switching or combining different drilling technologies as needed. Drilling rigs can be described using any of the following attributes.
mantan Drilling, 2017-12-03 02:54:13. Small to medium-sized drilling rigs are mobile, such as those used in mineral exploration drilling, blast-hole, water wells and environmental investigations. Larger rigs are capable of drilling through thousands of metres of the Earth s crust, using large "mud pumps" to circulate drilling mud (slurry) through the drill bit and up the casing annulus, for cooling and removing the "cuttings" while a well is drilled.
mantan Drilling, 2017-12-03 02:54:37. Some light duty drilling rigs are like a mobile crane and are more usually used to drill water wells. Larger land rigs must be broken apart into sections and loads to move to a new place, a process which can often take weeks.
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does thomaskc.com claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.