dakota excavator, 2017-12-29 03:05:15. Hydraulic excavators usually couple engine power to (commonly) three hydraulic pumps rather than to mechanical drivetrains. The two main pumps supply oil at high pressure (up to 5000 psi) for the arms, swing motor, track motors and accessories while the third is a lower pressure (~700 psi) pump for pilot control of the spool valves; this third circuit allows for reduced physical effort when operating the controls. Generally, the 3 pumps used in excavators consist of 2 variable displacement piston pumps and a gear pump. The arrangement of the pumps in the excavator unit changes with different manufacturers using different formats.
dakota excavator, 2017-12-29 03:06:05. Wheel excavator runs on wheels and are used for excavation and loading of dump trucks and most of the time it is only used for plain ground operations. Because of wheel, it is not suitable for hilly areas due to low grip value to the ground.
dakota excavator, 2017-12-29 03:06:03. Modern hydraulic excavators come in a wide variety of sizes. The smaller ones are called mini or compact excavators. For example, Caterpillarás smallest mini-excavator weighs 2,060 pounds (930 kg) and has 13 hp; their largest model is the largest excavator available (a record previously held by the Orenstein & Koppel RH400), the CAT 6090, which weighs in excess of 2,160,510 pounds (979,990 kg), has 4500 hp, and a bucket as large as 52.0 m³.
mr.wicks Drilling, 2017-11-17 07:38:35. Small to medium-sized drilling rigs are mobile, such as those used in mineral exploration drilling, blast-hole, water wells and environmental investigations. Larger rigs are capable of drilling through thousands of metres of the Earth s crust, using large "mud pumps" to circulate drilling mud (slurry) through the drill bit and up the casing annulus, for cooling and removing the "cuttings" while a well is drilled.
mr.wicks Drilling, 2017-11-16 15:34:10. The drilling mechanisms outlined below differ mechanically in terms of the machinery used, but also in terms of the method by which drill cuttings are removed from the cutting face of the drill and returned to surface.
mr.wicks Drilling, 2017-11-17 05:04:53. Some light duty drilling rigs are like a mobile crane and are more usually used to drill water wells. Larger land rigs must be broken apart into sections and loads to move to a new place, a process which can often take weeks.
mr.wicks Drilling, 2017-11-16 16:28:38. Hoists in the rig can lift hundreds of tons of pipe. Other equipment can force acid or sand into reservoirs to facilitate extraction of the oil or natural gas; and in remote locations there can be permanent living accommodation and catering for crews (which may be more than a hundred). Marine rigs may operate thousands of miles distant from the supply base with infrequent crew rotation or cycle.
mr.wicks Drilling, 2017-11-16 16:26:59. New portable drillcat technology uses smaller portable trailer mounted rigs with shorter 3-metre (10 ft) drill pipe. The shorter drill pipe also allows a much smaller mast. Portable trailer mounted drilling rigs have drill ratings from 90 to 200 metres (300 to 800 ft) depending on mud pump flow and pressure ratings and drill pipe sizes.
mr.wicks Drilling, 2017-11-16 11:38:19. Mining drilling rigs are used for two main purposes, exploration drilling which aims to identify the location and quality of a mineral, and production drilling, used in the production-cycle for mining.
mr.wicks Drilling, 2017-11-16 09:39:12. Small to medium-sized drilling rigs are mobile, such as those used in mineral exploration drilling, blast-hole, water wells and environmental investigations. Larger rigs are capable of drilling through thousands of metres of the Earth s crust, using large "mud pumps" to circulate drilling mud (slurry) through the drill bit and up the casing annulus, for cooling and removing the "cuttings" while a well is drilled.
mr.wicks Drilling, 2017-11-16 16:42:35. RAB drilling at extreme depth, if it encounters water, may rapidly clog the outside of the hole with debris, precluding removal of drill cuttings from the hole. This can be counteracted, however, with the use of "stabilizers" also known as "reamers", which are large cylindrical pieces of steel attached to the drill string, and made to perfectly fit the size of the hole being drilled. These have sets of rollers on the side, usually with tungsten buttons, that constantly break down cuttings being pushed upwards.
mr.wicks Drilling, 2017-11-16 07:46:56. There are many types and designs of drilling rigs, with many drilling rigs capable of switching or combining different drilling technologies as needed. Drilling rigs can be described using any of the following attributes.
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does Thomaskc.com claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.