dakota bulldozer, 2018-01-07 01:43:53. With the Closed-center Load Sensing (CLSS) hydraulic system, blade lever stroke is directly proportional with blade speed, regardless of the load and travel speed. This results in superb, fine controllability.
dakota bulldozer, 2018-01-07 01:44:00. Powerful S6D125E-2 diesel engine provides a massive output of 149 kW 200 HP. The engine power is transmitted smoothly to the final drives via a high-efficiency torque converter.
dakota bulldozer, 2018-01-07 01:44:05. Air filters and a higher internal air pressure combine to prevent external dust from entering the cab. In addition, the cab's hexagonal design provides excellent front, side, and rear visibility. The viscous damper cab suspension softens shocks for operator comfort and extends component life.
mr.wicks Drilling, 2017-09-18 09:18:38. Drilling rigs can sample sub-surface mineral deposits, test rock, soil and groundwater physical properties, and also can be used to install sub-surface fabrications, such as underground utilities, instrumentation, tunnels or wells.
mr.wicks Drilling, 2017-09-18 11:05:41. Drilling rigs can be mobile equipment mounted on trucks, tracks or trailers, or more permanent land or marine-based structures (such as oil platforms, commonly called offshore oil rigs even if they don t contain a drilling rig). The term "rig" therefore generally refers to the complex equipment that is used to penetrate the surface of the Earth s crust.
mr.wicks Drilling, 2017-09-18 10:25:46. RAB drilling at extreme depth, if it encounters water, may rapidly clog the outside of the hole with debris, precluding removal of drill cuttings from the hole. This can be counteracted, however, with the use of "stabilizers" also known as "reamers", which are large cylindrical pieces of steel attached to the drill string, and made to perfectly fit the size of the hole being drilled. These have sets of rollers on the side, usually with tungsten buttons, that constantly break down cuttings being pushed upwards.
mr.wicks Drilling, 2017-09-17 19:41:04. Hoists in the rig can lift hundreds of tons of pipe. Other equipment can force acid or sand into reservoirs to facilitate extraction of the oil or natural gas; and in remote locations there can be permanent living accommodation and catering for crews (which may be more than a hundred). Marine rigs may operate thousands of miles distant from the supply base with infrequent crew rotation or cycle.
mr.wicks Drilling, 2017-09-18 12:00:12. Oil and natural gas drilling rigs are used not only to identify geologic reservoirs but also to create holes that allow the extraction of oil or natural gas from those reservoirs. Primarily in onshore oil and gas fields once a well has been drilled, the drilling rig will be moved off of the well and a service rig (a smaller rig) that is purpose-built for completions will be moved on to the well to get the well on line.
mr.wicks Drilling, 2017-09-17 19:55:22. Some light duty drilling rigs are like a mobile crane and are more usually used to drill water wells. Larger land rigs must be broken apart into sections and loads to move to a new place, a process which can often take weeks.
mr.wicks Drilling, 2017-09-18 10:01:18. Auger drilling is done with a helical screw which is driven into the ground with rotation; the earth is lifted up the borehole by the blade of the screw. Hollow stem auger drilling is used for softer ground such as swamps where the hole will not stay open by itself for environmental drilling, geotechnical drilling, soil engineering and geochemistry reconnaissance work in exploration for mineral deposits.
mr.wicks Drilling, 2017-09-17 19:45:52. Large truck drills can use over 570 litres (150 US gal) of fuel per day, while the smaller Deeprock Style portable drills use a mere 20 to 75 litres (5 to 20 US gal) of fuel per day. This makes smaller, more portable rigs preferable in remote or hard-to-reach places, and they are more cost effective when fuel prices are high.
mr.wicks Drilling, 2017-09-18 12:07:49. RAB drilling is used most frequently in the mineral exploration industry. (This tool is also known as a Down-the-hole drill.) The drill uses a pneumatic reciprocating piston-driven "hammer" to energetically drive a heavy drill bit into the rock. The drill bit is hollow, solid steel and has ~20 mm thick tungsten rods protruding from the steel matrix as "buttons". The tungsten buttons are the cutting face of the bit.
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does Thomaskc.com claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.