dakota excavator, 2017-12-29 03:05:15. Crawler excavator runs on two endless tracks (chain wheel system). These types of excavators are used in hilly areas where risks of sliding of machinery are on the verge. Crawler type excavator has low ground pressure because of spreading of load on large area. Therefore, it is also used where soil support is weak.
dakota excavator, 2017-12-29 03:06:05. Excavator is the machine that can excavate the soil of various types forcefully and then using hydraulic system a hydraulic force is generated and utilizing this force bucket is pull back towards the machine. Bucket of excavator is replaceable. If front bucket is exchange with some other attachments then excavator can be used for multi-purpose. For example: pile diver, hydraulic jack hammer etc…
dakota excavator, 2017-12-29 03:06:03. Excavator is the machine that can excavate the soil of various types forcefully and then using hydraulic system a hydraulic force is generated and utilizing this force bucket is pull back towards the machine. Bucket of excavator is replaceable. If front bucket is exchange with some other attachments then excavator can be used for multi-purpose. For example: pile diver, hydraulic jack hammer etc…
mantan Drilling, 2017-12-03 02:41:29. There are a variety of drill mechanisms which can be used to sink a borehole into the ground. Each has its advantages and disadvantages, in terms of the depth to which it can drill, the type of sample returned, the costs involved and penetration rates achieved. There are two basic types of drills: drills which produce rock chips, and drills which produce core samples.
mantan Drilling, 2017-12-03 02:41:29. A drilling rig is a machine that creates holes in the earth sub-surface. Drilling rigs can be massive structures housing equipment used to drill water wells, oil wells, or natural gas extraction wells, or they can be small enough to be moved manually by one person and are called augers.
mantan Drilling, 2017-12-03 02:41:29. The drilling mechanisms outlined below differ mechanically in terms of the machinery used, but also in terms of the method by which drill cuttings are removed from the cutting face of the drill and returned to surface.
mantan Drilling, 2017-12-03 02:41:30. There are many types and designs of drilling rigs, with many drilling rigs capable of switching or combining different drilling technologies as needed. Drilling rigs can be described using any of the following attributes.
mantan Drilling, 2017-12-03 02:41:30. Auger drilling is done with a helical screw which is driven into the ground with rotation; the earth is lifted up the borehole by the blade of the screw. Hollow stem auger drilling is used for softer ground such as swamps where the hole will not stay open by itself for environmental drilling, geotechnical drilling, soil engineering and geochemistry reconnaissance work in exploration for mineral deposits.
mantan Drilling, 2017-12-03 02:41:30. In early oil exploration, drilling rigs were semi-permanent in nature and the derricks were often built on site and left in place after the completion of the well. In more recent times drilling rigs are expensive custom-built machines that can be moved from well to well.
mantan Drilling, 2017-12-03 02:41:30. New portable drillcat technology uses smaller portable trailer mounted rigs with shorter 3-metre (10 ft) drill pipe. The shorter drill pipe also allows a much smaller mast. Portable trailer mounted drilling rigs have drill ratings from 90 to 200 metres (300 to 800 ft) depending on mud pump flow and pressure ratings and drill pipe sizes.
mantan Drilling, 2017-12-03 02:41:29. Hoists in the rig can lift hundreds of tons of pipe. Other equipment can force acid or sand into reservoirs to facilitate extraction of the oil or natural gas; and in remote locations there can be permanent living accommodation and catering for crews (which may be more than a hundred). Marine rigs may operate thousands of miles distant from the supply base with infrequent crew rotation or cycle.
mantan Drilling, 2017-12-03 02:41:44. RAB drilling at extreme depth, if it encounters water, may rapidly clog the outside of the hole with debris, precluding removal of drill cuttings from the hole. This can be counteracted, however, with the use of "stabilizers" also known as "reamers", which are large cylindrical pieces of steel attached to the drill string, and made to perfectly fit the size of the hole being drilled. These have sets of rollers on the side, usually with tungsten buttons, that constantly break down cuttings being pushed upwards.
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does thomaskc.com claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.