dakota bulldozer, 2018-01-07 01:44:05. A flat bottom frame,the monocoque track frames and forward-mounted pivot shafts provide good maneuverability in muddy terrain by preventing mud from building up under the frame.
dakota bulldozer, 2018-01-07 01:43:53. Powerful S6D125E-2 diesel engine provides a massive output of 149 kW 200 HP. The engine power is transmitted smoothly to the final drives via a high-efficiency torque converter.
dakota bulldozer, 2018-01-07 01:44:00. With the Closed-center Load Sensing (CLSS) hydraulic system, blade lever stroke is directly proportional with blade speed, regardless of the load and travel speed. This results in superb, fine controllability.
mr.wicks Drilling, 2017-09-16 07:53:14. New portable drillcat technology uses smaller portable trailer mounted rigs with shorter 3-metre (10 ft) drill pipe. The shorter drill pipe also allows a much smaller mast. Portable trailer mounted drilling rigs have drill ratings from 90 to 200 metres (300 to 800 ft) depending on mud pump flow and pressure ratings and drill pipe sizes.
mr.wicks Drilling, 2017-09-15 19:38:52. This section does not cite any sources. Please help improve this section by adding citations to reliable sources. Unsourced material may be challenged and removed. (April 2011) (Learn how and when to remove this template message).
mr.wicks Drilling, 2017-09-16 08:20:29. Until internal combustion engines were developed in the late 19th century, the main method for drilling rock was muscle power of man or animal. The drilling of wells for the manufacture of salt began by the Song Dynasty in China.
mr.wicks Drilling, 2017-09-15 19:21:35. RAB drilling at extreme depth, if it encounters water, may rapidly clog the outside of the hole with debris, precluding removal of drill cuttings from the hole. This can be counteracted, however, with the use of "stabilizers" also known as "reamers", which are large cylindrical pieces of steel attached to the drill string, and made to perfectly fit the size of the hole being drilled. These have sets of rollers on the side, usually with tungsten buttons, that constantly break down cuttings being pushed upwards.
mr.wicks Drilling, 2017-09-16 04:03:06. Hoists in the rig can lift hundreds of tons of pipe. Other equipment can force acid or sand into reservoirs to facilitate extraction of the oil or natural gas; and in remote locations there can be permanent living accommodation and catering for crews (which may be more than a hundred). Marine rigs may operate thousands of miles distant from the supply base with infrequent crew rotation or cycle.
pascelina Drilling, 2017-09-15 19:43:26. Drilling rigs can be mobile equipment mounted on trucks, tracks or trailers, or more permanent land or marine-based structures (such as oil platforms, commonly called offshore oil rigs even if they don t contain a drilling rig). The term "rig" therefore generally refers to the complex equipment that is used to penetrate the surface of the Earth s crust.
mr.wicks Drilling, 2017-09-15 18:54:50. Other, heavier, truck rigs are more complicated, thus requiring more skill to run. They re also more difficult to handle safely due to the longer 6-to-9-metre (20 to 30 ft) drill pipe. Large truck rigs also require a much higher overhead clearance to operate.
mr.wicks Drilling, 2017-09-16 04:05:53. RAB drilling is used most frequently in the mineral exploration industry. (This tool is also known as a Down-the-hole drill.) The drill uses a pneumatic reciprocating piston-driven "hammer" to energetically drive a heavy drill bit into the rock. The drill bit is hollow, solid steel and has ~20 mm thick tungsten rods protruding from the steel matrix as "buttons". The tungsten buttons are the cutting face of the bit.
mr.wicks Drilling, 2017-09-15 19:45:43. RAB drilling at extreme depth, if it encounters water, may rapidly clog the outside of the hole with debris, precluding removal of drill cuttings from the hole. This can be counteracted, however, with the use of "stabilizers" also known as "reamers", which are large cylindrical pieces of steel attached to the drill string, and made to perfectly fit the size of the hole being drilled. These have sets of rollers on the side, usually with tungsten buttons, that constantly break down cuttings being pushed upwards.
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does thomaskc.com claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.