dakota excavator, 2017-12-29 03:06:05. Excavator comes in numerous sizes depending on bucket size, length of boom, length of arm, and operation speed. Performance of excavator can be measured from the production cycle. Production cycle is the time that an excavator took to load the bucket from source, swing, dump, return back and then dig again. Therefore, faster the operation speed, the faster will be the one complete cycle and hence production cycle will increase.
dakota excavator, 2017-12-29 03:05:15. Crawler excavator runs on two endless tracks (chain wheel system). These types of excavators are used in hilly areas where risks of sliding of machinery are on the verge. Crawler type excavator has low ground pressure because of spreading of load on large area. Therefore, it is also used where soil support is weak.
dakota excavator, 2017-12-29 03:06:03. An excavator is extremely useful for the construction industry, and can perform gigantic tasks that may not be possible by the human effort. Thus, the excavator has increased the speed of work to a great extent. Efforts are being made to reduce the excavator weight, and make it a quiet function.
mantan Drilling, 2017-12-03 03:02:15. RAB drilling is used primarily for mineral exploration, water bore drilling and blast-hole drilling in mines, as well as for other applications such as engineering, etc. RAB produces lower quality samples because the cuttings are blown up the outside of the rods and can be contaminated from contact with other rocks.
mantan Drilling, 2017-12-03 03:02:14. There are a variety of drill mechanisms which can be used to sink a borehole into the ground. Each has its advantages and disadvantages, in terms of the depth to which it can drill, the type of sample returned, the costs involved and penetration rates achieved. There are two basic types of drills: drills which produce rock chips, and drills which produce core samples.
mantan Drilling, 2017-12-03 03:02:15. The drilling mechanisms outlined below differ mechanically in terms of the machinery used, but also in terms of the method by which drill cuttings are removed from the cutting face of the drill and returned to surface.
mantan Drilling, 2017-12-03 03:02:16. A drilling rig is a machine that creates holes in the earth sub-surface. Drilling rigs can be massive structures housing equipment used to drill water wells, oil wells, or natural gas extraction wells, or they can be small enough to be moved manually by one person and are called augers.
mantan Drilling, 2017-12-03 03:02:14. Oil and natural gas drilling rigs are used not only to identify geologic reservoirs but also to create holes that allow the extraction of oil or natural gas from those reservoirs. Primarily in onshore oil and gas fields once a well has been drilled, the drilling rig will be moved off of the well and a service rig (a smaller rig) that is purpose-built for completions will be moved on to the well to get the well on line.
mantan Drilling, 2017-12-03 03:02:15. Other, heavier, truck rigs are more complicated, thus requiring more skill to run. They re also more difficult to handle safely due to the longer 6-to-9-metre (20 to 30 ft) drill pipe. Large truck rigs also require a much higher overhead clearance to operate.
mantan Drilling, 2017-12-03 03:02:15. RAB drilling is used most frequently in the mineral exploration industry. (This tool is also known as a Down-the-hole drill.) The drill uses a pneumatic reciprocating piston-driven "hammer" to energetically drive a heavy drill bit into the rock. The drill bit is hollow, solid steel and has ~20 mm thick tungsten rods protruding from the steel matrix as "buttons". The tungsten buttons are the cutting face of the bit.
mantan Drilling, 2017-12-03 03:02:16. In early oil exploration, drilling rigs were semi-permanent in nature and the derricks were often built on site and left in place after the completion of the well. In more recent times drilling rigs are expensive custom-built machines that can be moved from well to well.
mantan Drilling, 2017-12-03 03:02:14. Auger drilling is done with a helical screw which is driven into the ground with rotation; the earth is lifted up the borehole by the blade of the screw. Hollow stem auger drilling is used for softer ground such as swamps where the hole will not stay open by itself for environmental drilling, geotechnical drilling, soil engineering and geochemistry reconnaissance work in exploration for mineral deposits.
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does Thomaskc.com claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.