dakota excavator, 2017-12-29 03:05:15. Attached to the end of the boom is the stick (or dipper arm). The stick provides the digging force needed to pull the bucket through the ground. The stick length is optional depending whether reach (longer stick) or break-out power (shorter stick) is required.
dakota excavator, 2017-12-29 03:06:05. The two main sections of an excavator are the undercarriage and the house. The undercarriage includes the blade (if fitted), tracks, track frame, and final drives, which have a hydraulic motor and gearing providing the drive to the individual tracks, and the house includes the operator cab, counterweight, engine, fuel and hydraulic oil tanks. The house attaches to the undercarriage by way of a center pin. High pressure oil is supplied to the tracksá hydraulic motors through a hydraulic swivel at the axis of the pin, allowing the machine to slew 360° unhindered.
dakota excavator, 2017-12-29 03:06:03. Excavator comes in numerous sizes depending on bucket size, length of boom, length of arm, and operation speed. Performance of excavator can be measured from the production cycle. Production cycle is the time that an excavator took to load the bucket from source, swing, dump, return back and then dig again. Therefore, faster the operation speed, the faster will be the one complete cycle and hence production cycle will increase.
mr.wicks Drilling, 2017-09-06 06:30:23. RAB drilling is used most frequently in the mineral exploration industry. (This tool is also known as a Down-the-hole drill.) The drill uses a pneumatic reciprocating piston-driven "hammer" to energetically drive a heavy drill bit into the rock. The drill bit is hollow, solid steel and has ~20 mm thick tungsten rods protruding from the steel matrix as "buttons". The tungsten buttons are the cutting face of the bit.
mr.wicks Drilling, 2017-09-06 16:08:33. RC drilling proved much faster and more efficient, and continues to improve with better metallurgy, deriving harder, more durable bits, and compressors delivering higher air pressures at higher volumes, enabling deeper and faster penetration. Diamond drilling has remained essentially unchanged since its inception.
mr.wicks Drilling, 2017-09-07 08:38:53. Oil and natural gas drilling rigs are used not only to identify geologic reservoirs but also to create holes that allow the extraction of oil or natural gas from those reservoirs. Primarily in onshore oil and gas fields once a well has been drilled, the drilling rig will be moved off of the well and a service rig (a smaller rig) that is purpose-built for completions will be moved on to the well to get the well on line.
mr.wicks Drilling, 2017-09-06 10:02:15. There are many types and designs of drilling rigs, with many drilling rigs capable of switching or combining different drilling technologies as needed. Drilling rigs can be described using any of the following attributes.
mr.wicks Drilling, 2017-09-06 10:42:54. Antique drilling rig now on display at Western History Museum in Lingle, Wyoming. It was used to drill many water wells in that area—many of those wells are still in use.
mr.wicks Drilling, 2017-09-06 14:10:47. There are many types and designs of drilling rigs, with many drilling rigs capable of switching or combining different drilling technologies as needed. Drilling rigs can be described using any of the following attributes.
mr.wicks Drilling, 2017-09-07 12:15:14. In the 1970s, outside of the oil and gas industry, roller bits using mud circulation were replaced by the first pneumatic reciprocating piston Reverse Circulation (RC) drills, and became essentially obsolete for most shallow drilling, and are now only used in certain situations where rocks preclude other methods.
mr.wicks Drilling, 2017-09-06 04:38:43. Drilling rigs used for rock blasting for surface mines vary in size dependent on the size of the hole desired, and is typically classified into smaller pre-split and larger production holes. Underground mining (hard rock) uses a variety of drill rigs dependent on the desired purpose, such as production, bolting, cabling, and tunnelling.
mr.wicks Drilling, 2017-09-06 17:20:15. Other, heavier, truck rigs are more complicated, thus requiring more skill to run. They re also more difficult to handle safely due to the longer 6-to-9-metre (20 to 30 ft) drill pipe. Large truck rigs also require a much higher overhead clearance to operate.
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does Thomaskc.com claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.