dakota excavator, 2017-12-29 03:06:03. Hydraulic excavators usually couple engine power to (commonly) three hydraulic pumps rather than to mechanical drivetrains. The two main pumps supply oil at high pressure (up to 5000 psi) for the arms, swing motor, track motors and accessories while the third is a lower pressure (~700 psi) pump for pilot control of the spool valves; this third circuit allows for reduced physical effort when operating the controls. Generally, the 3 pumps used in excavators consist of 2 variable displacement piston pumps and a gear pump. The arrangement of the pumps in the excavator unit changes with different manufacturers using different formats.
dakota excavator, 2017-12-29 03:05:15. Before the 1990s, all excavators had a long or conventional counterweight that hung off the rear of the machine to provide more digging force and lifting capacity. This became a nuisance when working in confined areas. In 1993 Yanmar launched the worldás first Zero Tail Swing excavator, which allows the counterweight to stay inside the width of the tracks as it slews, thus being safer and more user friendly when used in a confined space. This type of machine is now widely used throughout the world.
dakota excavator, 2017-12-29 03:06:05. Excavator comes in numerous sizes depending on bucket size, length of boom, length of arm, and operation speed. Performance of excavator can be measured from the production cycle. Production cycle is the time that an excavator took to load the bucket from source, swing, dump, return back and then dig again. Therefore, faster the operation speed, the faster will be the one complete cycle and hence production cycle will increase.
mr.wicks Drilling, 2017-08-19 11:31:07. Small to medium-sized drilling rigs are mobile, such as those used in mineral exploration drilling, blast-hole, water wells and environmental investigations. Larger rigs are capable of drilling through thousands of metres of the Earth s crust, using large "mud pumps" to circulate drilling mud (slurry) through the drill bit and up the casing annulus, for cooling and removing the "cuttings" while a well is drilled.
mr.wicks Drilling, 2017-08-19 07:29:49. Drilling rigs can sample sub-surface mineral deposits, test rock, soil and groundwater physical properties, and also can be used to install sub-surface fabrications, such as underground utilities, instrumentation, tunnels or wells.
mr.wicks Drilling, 2017-08-19 10:06:14. This frees up the drilling rig to drill another hole and streamlines the operation as well as allowing for specialization of certain services, i.e., completions vs. drilling.
mr.wicks Drilling, 2017-08-19 05:27:28. A drilling rig is a machine that creates holes in the earth sub-surface. Drilling rigs can be massive structures housing equipment used to drill water wells, oil wells, or natural gas extraction wells, or they can be small enough to be moved manually by one person and are called augers.
mr.wicks Drilling, 2017-08-19 05:15:57. There are a variety of drill mechanisms which can be used to sink a borehole into the ground. Each has its advantages and disadvantages, in terms of the depth to which it can drill, the type of sample returned, the costs involved and penetration rates achieved. There are two basic types of drills: drills which produce rock chips, and drills which produce core samples.
mr.wicks Drilling, 2017-08-19 09:57:30. RAB drilling at extreme depth, if it encounters water, may rapidly clog the outside of the hole with debris, precluding removal of drill cuttings from the hole. This can be counteracted, however, with the use of "stabilizers" also known as "reamers", which are large cylindrical pieces of steel attached to the drill string, and made to perfectly fit the size of the hole being drilled. These have sets of rollers on the side, usually with tungsten buttons, that constantly break down cuttings being pushed upwards.
mr.wicks Drilling, 2017-08-20 04:20:10. Other, heavier, truck rigs are more complicated, thus requiring more skill to run. They re also more difficult to handle safely due to the longer 6-to-9-metre (20 to 30 ft) drill pipe. Large truck rigs also require a much higher overhead clearance to operate.
mr.wicks Drilling, 2017-08-19 08:11:48. Hoists in the rig can lift hundreds of tons of pipe. Other equipment can force acid or sand into reservoirs to facilitate extraction of the oil or natural gas; and in remote locations there can be permanent living accommodation and catering for crews (which may be more than a hundred). Marine rigs may operate thousands of miles distant from the supply base with infrequent crew rotation or cycle.
mr.wicks Drilling, 2017-08-19 10:47:00. Oil and natural gas drilling rigs are used not only to identify geologic reservoirs but also to create holes that allow the extraction of oil or natural gas from those reservoirs. Primarily in onshore oil and gas fields once a well has been drilled, the drilling rig will be moved off of the well and a service rig (a smaller rig) that is purpose-built for completions will be moved on to the well to get the well on line.
Any content, trademark/s, or other material that might be found on this site that is not this site property remains the copyright of its respective owner/s. In no way does thomaskc.com claim ownership or responsibility for such items, and you should seek legal consent for any use of such materials from its owner.